[AusNOG] Issue with configuration on VYOS

[Shane Short]

+1

Daniel,
AusNOG isn't your personal support platform-- many of the questions you 
ask here are *simple* to find by spending a few minutes searching 
around. I'd suggest spending quite a few minutes trying to solve things 
yourself, and leaving the list for problems where you're genuinely 
stuck-- otherwise people might stop humouring you and stop responding to 
your questions.

-Shane

Tim Raphael wrote:
> Daniel:
>
> You need to stop assuming and start reading the plentiful amount of 
> documentation available on how to do a VyOS upgrade or install. A 
> basic, 2 minute google search will highlight a link on Vyos.net 
> <http://Vyos.net> about "How to migrate from Vyatta" which answers all 
> your questions.
>
> Good luck with the upgrade.
>
> Regards,
>
> Tim Raphael
>
> On 26 Aug 2014, at 5:45 pm, Daniel Watson <Daniel at glovine.com.au 
> <mailto:Daniel at glovine.com.au>> wrote:
>
>> Hi Nathan
>>
>> I can only assume its just a standard “install system” once the ISO 
>> is mounted and booted?
>>
>> Once the install has finished, I powered down the VM, edited the VM 
>> settings and unmounted the ISO and then powered it up, and ran my 
>> configurations
>>
>> Regards,
>>
>> Daniel Watson
>>
>> Network Administrator / Network Operations Manager
>>
>> E Daniel at GloVine.com.au <mailto:Daniel at GloVine.com.au>
>>
>> W www.GloVine.com.au <http://www.GloVine.com.au>
>>
>> *From:*Nathan Brookfield [mailto:Nathan.Brookfield at simtronic.com.au]
>> *Sent:* Tuesday, 26 August 2014 7:46 PM
>> *To:* Daniel Watson
>> *Cc:* Damien Gardner Jnr; ausnog at lists.ausnog.net 
>> <mailto:ausnog at lists.ausnog.net>; 
>> (nick.pratley at serversaustralia.com.au 
>> <mailto:nick.pratley at serversaustralia.com.au>); Jiri Kosar
>> *Subject:* Re: Issue with configuration on VYOS
>>
>> I agree with Damien, it sounds like it had not installed to the file 
>> system correctly and is using a volatile imagine
>>
>> Kindest Regards,
>>
>> Nathan Brookfield
>>
>> Chief Executive Officer
>>
>> Simtronic Technologies Pty Ltd
>>
>> Web: http://simtronic.com.au
>>
>> Phone: 1300 592 330
>>
>> Fax: (02) 4749 4950
>>
>>
>> On 26 Aug 2014, at 19:44, "Daniel Watson" <Daniel at glovine.com.au 
>> <mailto:Daniel at glovine.com.au>> wrote:
>>
>> Indeedy :D
>>
>> I first didn’t.. but then realised,  unmounted the ISO, rebooted and 
>> applied the config once AGAIN  and then repeated the rebooting, and 
>> still nutter..
>>
>> I am currently installing another Vyatta VM atm, going to apply the 
>> config, as I know it works on Vyatta, and then do a run over with the 
>> VYOS image and convert it to vyos   and see if it saves the config on 
>> reboot that way…
>>
>> Regards,
>>
>> Daniel Watson
>>
>> Network Administrator / Network Operations Manager
>>
>> E Daniel at GloVine.com.au <mailto:Daniel at GloVine.com.au>
>>
>> W www.GloVine.com.au <http://www.GloVine.com.au>
>>
>> *From:*Damien Gardner Jnr [mailto:rendrag at rendrag.net]
>> *Sent:* Tuesday, 26 August 2014 7:40 PM
>> *To:* Daniel Watson
>> *Cc:* ausnog at lists.ausnog.net <mailto:ausnog at lists.ausnog.net>; 
>> Nathan Brookfield; (nick.pratley at serversaustralia.com.au 
>> <mailto:nick.pratley at serversaustralia.com.au>); Jiri Kosar
>> *Subject:* Re: Issue with configuration on VYOS
>>
>> Dumb question, but have you unmounted the install image?  That 
>> confused the heck out of me the first time I installed it, till i 
>> realised it'd booted from the CD instead of the hard disk..
>>
>> --DG
>>
>> On 26 August 2014 19:31, Daniel Watson <Daniel at glovine.com.au 
>> <mailto:Daniel at glovine.com.au>> wrote:
>>
>>     Hi Guys
>>
>>     Okay so ive just installed a VYOS router in my dev environment,
>>
>>     I have configured it all up, adding IP’s and protocols and routes ect
>>
>>     I have then attempted to save and commit the config which has
>>     worked fine by running the following commands
>>
>>     Save
>>
>>     Commit
>>
>>     Then I have exited out of the configuration mode, and restarted
>>     the router,
>>
>>     Once the router has rebooted, ive logged back in  but NOTHING is
>>     there.. its almost like the config wasn’t saved properly when I
>>     typed save…
>>
>>     Does anybody have any ideas what im doing wrong here?
>>
>>     Regards,
>>
>>     Daniel Watson
>>
>>     Network Administrator / Network Operations Manager
>>
>>     E Daniel at GloVine.com.au <mailto:Daniel at GloVine.com.au>
>>
>>     W www.GloVine.com.au <http://www.GloVine.com.au>
>>
>>
>>
>> -- 
>>
>> Damien Gardner Jnr
>> VK2TDG. Dip EE. GradIEAust
>> rendrag at rendrag.net <mailto:rendrag at rendrag.net> - 
>> http://www.rendrag.net/_
>> _--
>> We rode on the winds of the rising storm,
>>  We ran to the sounds of thunder.
>> We danced among the lightning bolts,
>>  and tore the world asunder
>>
>> _______________________________________________
>> AusNOG mailing list
>> AusNOG at lists.ausnog.net <mailto:AusNOG at lists.ausnog.net>
>> http://lists.ausnog.net/mailman/listinfo/ausnog
> _______________________________________________
> AusNOG mailing list
> AusNOG at lists.ausnog.net
> http://lists.ausnog.net/mailman/listinfo/ausnog
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ausnog.net/pipermail/ausnog/attachments/20140827/012cf689/attachment.html>