[AusNOG] Issue with configuration on VYOS

[Tim Raphael]

Daniel:

You need to stop assuming and start reading the plentiful amount of documentation available on how to do a VyOS upgrade or install. A basic, 2 minute google search will highlight a link on Vyos.net about "How to migrate from Vyatta" which answers all your questions.

Good luck with the upgrade.

Regards,

Tim Raphael

> On 26 Aug 2014, at 5:45 pm, Daniel Watson <Daniel at glovine.com.au> wrote:
> 
> Hi Nathan
>  
> I can only assume its just a standard “install system” once the ISO is mounted and booted?
>  
> Once the install has finished, I powered down the VM, edited the VM settings and unmounted the ISO and then powered it up, and ran my configurations
>  
>  
> Regards,
> Daniel Watson
> Network Administrator / Network Operations Manager
>  
> E Daniel at GloVine.com.au
> W www.GloVine.com.au
>  
> From: Nathan Brookfield [mailto:Nathan.Brookfield at simtronic.com.au] 
> Sent: Tuesday, 26 August 2014 7:46 PM
> To: Daniel Watson
> Cc: Damien Gardner Jnr; ausnog at lists.ausnog.net; (nick.pratley at serversaustralia.com.au); Jiri Kosar
> Subject: Re: Issue with configuration on VYOS
>  
> I agree with Damien, it sounds like it had not installed to the file system correctly and is using a volatile imagine
> 
> Kindest Regards,
> Nathan Brookfield
>  
> Chief Executive Officer
> Simtronic Technologies Pty Ltd
>  
> Web: http://simtronic.com.au
> Phone: 1300 592 330
> Fax: (02) 4749 4950
> 
> On 26 Aug 2014, at 19:44, "Daniel Watson" <Daniel at glovine.com.au> wrote:
> 
> Indeedy :D
>  
> I first didn’t.. but then realised,  unmounted the ISO, rebooted and applied the config once AGAIN  and then repeated the rebooting, and still nutter..
>  
> I am currently installing another Vyatta VM atm, going to apply the config, as I know it works on Vyatta, and then do a run over with the VYOS image and convert it to vyos   and see if it saves the config on reboot that way…
>  
>  
> Regards,
> Daniel Watson
> Network Administrator / Network Operations Manager
>  
> E Daniel at GloVine.com.au
> W www.GloVine.com.au
>  
> From: Damien Gardner Jnr [mailto:rendrag at rendrag.net] 
> Sent: Tuesday, 26 August 2014 7:40 PM
> To: Daniel Watson
> Cc: ausnog at lists.ausnog.net; Nathan Brookfield; (nick.pratley at serversaustralia.com.au); Jiri Kosar
> Subject: Re: Issue with configuration on VYOS
>  
> Dumb question, but have you unmounted the install image?  That confused the heck out of me the first time I installed it, till i realised it'd booted from the CD instead of the hard disk..
>  
> --DG
>  
> 
> On 26 August 2014 19:31, Daniel Watson <Daniel at glovine.com.au> wrote:
> Hi Guys
>  
> Okay so ive just installed a VYOS router in my dev environment, 
>  
> I have configured it all up, adding IP’s and protocols and routes ect
>  
> I have then attempted to save and commit the config which has worked fine by running the following commands
>  
> Save
> Commit
>  
>  
> Then I have exited out of the configuration mode, and restarted the router,
>  
> Once the router has rebooted, ive logged back in  but NOTHING is there.. its almost like the config wasn’t saved properly when I typed save…
>  
> Does anybody have any ideas what im doing wrong here?
>  
>  
> Regards,
> Daniel Watson
> Network Administrator / Network Operations Manager
>  
> E Daniel at GloVine.com.au
> W www.GloVine.com.au
>  
> 
> 
>  
> --
> Damien Gardner Jnr
> VK2TDG. Dip EE. GradIEAust
> rendrag at rendrag.net -  http://www.rendrag.net/
> --
> We rode on the winds of the rising storm,
>  We ran to the sounds of thunder.
> We danced among the lightning bolts,
>  and tore the world asunder
> 
> _______________________________________________
> AusNOG mailing list
> AusNOG at lists.ausnog.net
> http://lists.ausnog.net/mailman/listinfo/ausnog
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ausnog.net/pipermail/ausnog/attachments/20140826/fa3407e9/attachment-0001.html>