[AusNOG] Issue with configuration on VYOS

[Daniel Watson]

Hi Nathan

I can only assume its just a standard "install system" once the ISO is mounted and booted?

Once the install has finished, I powered down the VM, edited the VM settings and unmounted the ISO and then powered it up, and ran my configurations


Regards,
Daniel Watson
Network Administrator / Network Operations Manager

E Daniel at GloVine.com.au
W www.GloVine.com.au

From: Nathan Brookfield [mailto:Nathan.Brookfield at simtronic.com.au]
Sent: Tuesday, 26 August 2014 7:46 PM
To: Daniel Watson
Cc: Damien Gardner Jnr; ausnog at lists.ausnog.net; (nick.pratley at serversaustralia.com.au); Jiri Kosar
Subject: Re: Issue with configuration on VYOS

I agree with Damien, it sounds like it had not installed to the file system correctly and is using a volatile imagine
Kindest Regards,
Nathan Brookfield

Chief Executive Officer
Simtronic Technologies Pty Ltd

Web: http://simtronic.com.au
Phone: 1300 592 330
Fax: (02) 4749 4950

On 26 Aug 2014, at 19:44, "Daniel Watson" <Daniel at glovine.com.au<mailto:Daniel at glovine.com.au>> wrote:
Indeedy :D

I first didn't.. but then realised,  unmounted the ISO, rebooted and applied the config once AGAIN  and then repeated the rebooting, and still nutter..

I am currently installing another Vyatta VM atm, going to apply the config, as I know it works on Vyatta, and then do a run over with the VYOS image and convert it to vyos   and see if it saves the config on reboot that way...


Regards,
Daniel Watson
Network Administrator / Network Operations Manager

E Daniel at GloVine.com.au<mailto:Daniel at GloVine.com.au>
W www.GloVine.com.au<http://www.GloVine.com.au>

From: Damien Gardner Jnr [mailto:rendrag at rendrag.net]
Sent: Tuesday, 26 August 2014 7:40 PM
To: Daniel Watson
Cc: ausnog at lists.ausnog.net<mailto:ausnog at lists.ausnog.net>; Nathan Brookfield; (nick.pratley at serversaustralia.com.au<mailto:nick.pratley at serversaustralia.com.au>); Jiri Kosar
Subject: Re: Issue with configuration on VYOS

Dumb question, but have you unmounted the install image?  That confused the heck out of me the first time I installed it, till i realised it'd booted from the CD instead of the hard disk..

--DG

On 26 August 2014 19:31, Daniel Watson <Daniel at glovine.com.au<mailto:Daniel at glovine.com.au>> wrote:
Hi Guys

Okay so ive just installed a VYOS router in my dev environment,

I have configured it all up, adding IP's and protocols and routes ect

I have then attempted to save and commit the config which has worked fine by running the following commands

Save
Commit


Then I have exited out of the configuration mode, and restarted the router,

Once the router has rebooted, ive logged back in  but NOTHING is there.. its almost like the config wasn't saved properly when I typed save...

Does anybody have any ideas what im doing wrong here?


Regards,
Daniel Watson
Network Administrator / Network Operations Manager

E Daniel at GloVine.com.au<mailto:Daniel at GloVine.com.au>
W www.GloVine.com.au<http://www.GloVine.com.au>




--

Damien Gardner Jnr
VK2TDG. Dip EE. GradIEAust
rendrag at rendrag.net<mailto:rendrag at rendrag.net> -  http://www.rendrag.net/
--
We rode on the winds of the rising storm,
 We ran to the sounds of thunder.
We danced among the lightning bolts,
 and tore the world asunder
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ausnog.net/pipermail/ausnog/attachments/20140826/4281aa1b/attachment.html>