[AusNOG] Test lab storage / racking

Fri Aug 6 14:53:11 EST 2010

Cheers!
Karl Kloppenborg

On 06/08/2010, at 14:47, Curtis Bayne wrote:

> http://www.energymatters.com.au/latronics-automatic-transfer-switch-40amp-2way-ac-p-97.html
> 
> Much easier, but nowhere near as fun ;)
> 
> -----Original Message-----
> From: ausnog-bounces at lists.ausnog.net on behalf of Karl Kloppenborg
> Sent: Fri 8/6/2010 2:41 PM
> To: Sean K. Finn
> Cc: 'ausnog at ausnog.net'
> Subject: Re: [AusNOG] Test lab storage / racking
> 
> That wasn't hard to find,
> http://jaycar.com.au/productView.asp?ID=KV3600&CATID=25&form=CAT&SUBCATID=432
> 
> 
> You do have to do a bit more to it then just get that,
> 
> A)
> you need to setup a relay bank to handle the step up from 5v logic to 12 ignition to the genset (also the genset obviously needs to be keystart so you can logic replicate)
> 
> B) set a genMonitor, so when the power fails you go to UPS (just a high amp / voltage manual relay will suffice)
> 
> this monitor will trigger a logic signal back to the USB experimentation kit that triggers your visual basic program to start the gen up.
> 
> I set the system to wait 1.25 minutes for the genset to power on and then test to see if power is flowing through the gen circuit .
> 
> C) to monitor the gen circuit at jaycar you can buy some industrial power monitors (digital ones) that allow you to then wire into your setup (back to the USB experimentation board) a analog (important because its used to test the stability and cleanness of your gen output) back into the board which then interfaces with your visual basic program to then switch the jump relay over (5v relay to 12v relay to 240v to 240v High amp relay) to the backup circuit.
> 
> if the gen doesn't start I have it set to send me a fail sms and kill the program.. (poor servers go night night)
> 
> then when power gets restored you can sense that again using the same system as the gen circuit uses (you will need one for each circuit) and then switch the jump relays over to primary and shut genset over.
> 
> 
> easy :)
> 
> enjoy... I AM NOT RESPONSIBLE FOR ANY HOUSE FIRES!
> 
> Cheers!
> Karl Kloppenborg
> 
> 
> 
> 
> On 06/08/2010, at 14:25, Sean K. Finn wrote:
> 
> > Please link this Jaycar device, +1 Interesting.
> > 
> > 
> > From: ausnog-bounces at lists.ausnog.net [mailto:ausnog-bounces at lists.ausnog.net] On Behalf Of Karl Kloppenborg
> > Sent: Friday, 6 August 2010 2:24 PM
> > To: Thomas Storey
> > Cc: ausnog at ausnog.net
> > Subject: Re: [AusNOG] Test lab storage / racking
> > 
> > As some of you already have seen (Youtube) that I had a 42RU rack in my room,
> > 
> > I also had a 22 RU custom 1000mm deep rack that had its own really really loud cooling system.
> > My mother supported my enthusiasm for IT and let me run nuts with my dads credit cards on ebay buying stupid amounts of servers / switches / etc etc, to support it she had bill brower (our electrician) put a separate 20AMP feed into my room as well as some smoke detectors and different things... I am so thankful for their support.
> > 
> > I also had a small generator outside and built a failover high voltage relay switch that could be started from my computer using a USB to digi rail from Jaycar :)
> > 
> > In terms of moving equipment and what not I just bolted it in, had a few shelves and used to spend (wag) school some days like once every three months and just move it all around :P
> > 
> > 
> > Fun times, however I am yet to have a fire ;)
> > 
> >
> > Cheers!
> > Karl Kloppenborg
> > 
> >
> >
> >
> > 
> > On 06/08/2010, at 14:08, Thomas Storey wrote:
> >
> >
> > On the back of Seans emails, I have a home made *wooden* rack, about 15 RU, 700mm deep or so. :-)
> >
> > Tom
> >
> > On 05/08/2010, at 9:50 PM, Julien Goodwin wrote:
> >
> >
> > What do people do for their lab gear?
> > 
> > While a standard rack with shelves might be nicest for labs with heavy
> > gear swapping that usually means just using the shelves.
> > 
> > And for home use there's often space issues with a rack.
> > 
> > My own home lab is very quickly expanding and needs something more then
> > a pile in a corner of my home office (fortunately my personal M40e has
> > now been sold, or this would be a *much* bigger problem).
> > _______________________________________________
> > AusNOG mailing list
> > AusNOG at lists.ausnog.net
> > http://lists.ausnog.net/mailman/listinfo/ausnog
> >
> > _______________________________________________
> > AusNOG mailing list
> > AusNOG at lists.ausnog.net
> > http://lists.ausnog.net/mailman/listinfo/ausnog
> > 
> 
> 
> 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ausnog.net/pipermail/ausnog/attachments/20100806/df2a116f/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: PastedGraphic-1.pdf
Type: application/pdf
Size: 45829 bytes
Desc: not available
URL: <http://lists.ausnog.net/pipermail/ausnog/attachments/20100806/df2a116f/attachment.pdf>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ausnog.net/pipermail/ausnog/attachments/20100806/df2a116f/attachment-0001.html>