[AusNOG] Issue with configuration on VYOS

[Damien Gardner Jnr]

none on /opt/vyatta/config type tmpfs (rw,nosuid,nodev,mode=775,nr_inodes=0)

/opt/vyatta/etc/config on /config type none (rw,bind)


That'll do it ;)   Assuming /config is where your config is stored, it's on
a ramdisk rofl


On 26 August 2014 19:52, Daniel Watson <Daniel at glovine.com.au> wrote:

>  Gday Nick,
>
>
>
> /dev/sda1 on / type ext4 (rw,noatime)
>
> tmpfs on /lib/init/rw type tmpfs (rw,nosuid,mode=0755)
>
> proc on /proc type proc (rw,noexec,nosuid,nodev)
>
> sysfs on /sys type sysfs (rw,noexec,nosuid,nodev)
>
> udev on /dev type tmpfs (rw,mode=0755)
>
> tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev)
>
> devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=620)
>
> fusectl on /sys/fs/fuse/connections type fusectl (rw)
>
> none on /opt/vyatta/config type tmpfs
> (rw,nosuid,nodev,mode=775,nr_inodes=0)
>
> /opt/vyatta/etc/config on /config type none (rw,bind)
>
>
>
>
>
> Regards,
>
> Daniel Watson
>
> Network Administrator / Network Operations Manager
>
>
>
> E Daniel at GloVine.com.au
>
> W www.GloVine.com.au
>
>
>
> *From:* Nick Pratley [mailto:nick.pratley at serversaustralia.com.au]
> *Sent:* Tuesday, 26 August 2014 7:53 PM
> *To:* Daniel Watson
> *Cc:* Nathan Brookfield; Damien Gardner Jnr; ausnog at lists.ausnog.net;
> Jiri Kosar
>
> *Subject:* Re: Issue with configuration on VYOS
>
>
>
> Daniel,
>
>
>
> What does the output of
>
>
>
> sudo mount
>
> Or
>
> sudo mounts
>
>
>
> (Can't remember from the top of my head)
>
>
>
> Look like?
>
> Sent from my iPhone
>
>
> On 26 Aug 2014, at 7:48 pm, Daniel Watson <Daniel at glovine.com.au> wrote:
>
> Hi Nathan
>
>
>
> I can only assume its just a standard “install system” once the ISO is
> mounted and booted?
>
>
>
> Once the install has finished, I powered down the VM, edited the VM
> settings and unmounted the ISO and then powered it up, and ran my
> configurations
>
>
>
>
>
> Regards,
>
> Daniel Watson
>
> Network Administrator / Network Operations Manager
>
>
>
> E Daniel at GloVine.com.au
>
> W www.GloVine.com.au
>
>
>
> *From:* Nathan Brookfield [mailto:Nathan.Brookfield at simtronic.com.au
> <Nathan.Brookfield at simtronic.com.au>]
> *Sent:* Tuesday, 26 August 2014 7:46 PM
> *To:* Daniel Watson
> *Cc:* Damien Gardner Jnr; ausnog at lists.ausnog.net; (
> nick.pratley at serversaustralia.com.au); Jiri Kosar
> *Subject:* Re: Issue with configuration on VYOS
>
>
>
> I agree with Damien, it sounds like it had not installed to the file
> system correctly and is using a volatile imagine
>
> Kindest Regards,
>
> Nathan Brookfield
>
>
>
> Chief Executive Officer
>
> Simtronic Technologies Pty Ltd
>
>
>
> Web: http://simtronic.com.au
>
> Phone: 1300 592 330
>
> Fax: (02) 4749 4950
>
>
> On 26 Aug 2014, at 19:44, "Daniel Watson" <Daniel at glovine.com.au> wrote:
>
> Indeedy :D
>
>
>
> I first didn’t.. but then realised,  unmounted the ISO, rebooted and
> applied the config once AGAIN  and then repeated the rebooting, and still
> nutter..
>
>
>
> I am currently installing another Vyatta VM atm, going to apply the
> config, as I know it works on Vyatta, and then do a run over with the VYOS
> image and convert it to vyos   and see if it saves the config on reboot
> that way…
>
>
>
>
>
> Regards,
>
> Daniel Watson
>
> Network Administrator / Network Operations Manager
>
>
>
> E Daniel at GloVine.com.au
>
> W www.GloVine.com.au
>
>
>
> *From:* Damien Gardner Jnr [mailto:rendrag at rendrag.net
> <rendrag at rendrag.net>]
> *Sent:* Tuesday, 26 August 2014 7:40 PM
> *To:* Daniel Watson
> *Cc:* ausnog at lists.ausnog.net; Nathan Brookfield; (
> nick.pratley at serversaustralia.com.au); Jiri Kosar
> *Subject:* Re: Issue with configuration on VYOS
>
>
>
> Dumb question, but have you unmounted the install image?  That confused
> the heck out of me the first time I installed it, till i realised it'd
> booted from the CD instead of the hard disk..
>
>
>
> --DG
>
>
>
> On 26 August 2014 19:31, Daniel Watson <Daniel at glovine.com.au> wrote:
>
>  Hi Guys
>
>
>
> Okay so ive just installed a VYOS router in my dev environment,
>
>
>
> I have configured it all up, adding IP’s and protocols and routes ect
>
>
>
> I have then attempted to save and commit the config which has worked fine
> by running the following commands
>
>
>
> Save
>
> Commit
>
>
>
>
>
> Then I have exited out of the configuration mode, and restarted the router,
>
>
>
> Once the router has rebooted, ive logged back in  but NOTHING is there..
> its almost like the config wasn’t saved properly when I typed save…
>
>
>
> Does anybody have any ideas what im doing wrong here?
>
>
>
>
>
> Regards,
>
> Daniel Watson
>
> Network Administrator / Network Operations Manager
>
>
>
> E Daniel at GloVine.com.au
>
> W www.GloVine.com.au
>
>
>
>
>
>
>
> --
>
> Damien Gardner Jnr
> VK2TDG. Dip EE. GradIEAust
> rendrag at rendrag.net -  http://www.rendrag.net/
> --
> We rode on the winds of the rising storm,
>  We ran to the sounds of thunder.
> We danced among the lightning bolts,
>  and tore the world asunder
>



-- 

Damien Gardner Jnr
VK2TDG. Dip EE. GradIEAust
rendrag at rendrag.net -  http://www.rendrag.net/
--
We rode on the winds of the rising storm,
 We ran to the sounds of thunder.
We danced among the lightning bolts,
 and tore the world asunder
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ausnog.net/pipermail/ausnog/attachments/20140826/4f589f3b/attachment.html>