<div dir="ltr">Our last high density deployment we made a case to make every port on the floor live and just did 1RU Patch panel, 1RUswitch, 1RU patch panel, 1RU cable management, repeat. Then used 20cm patches to go direct from the patch panel immediately above and below each switch into the switch. Had the added bonus of no need to do any patch moves etc, just reconfigure the VLAN of the switchport. We were getting 288 ports into half a rack<div>
<br></div><div>--Damian</div></div><div class="gmail_extra"><br><br><div class="gmail_quote">On Tue, May 27, 2014 at 2:30 PM, Beeson, Ayden <span dir="ltr"><<a href="mailto:ABeeson@csu.edu.au" target="_blank">ABeeson@csu.edu.au</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div lang="EN-AU" link="blue" vlink="purple"><div><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d">Oh also, something we have used in the past is the Panduit 1 and 2 RU cable management, both closed and open.<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d">The 2RU closed one works fairly well for going between two flat 24 port panels, plenty of room for everything you need to fit though it’s a space waster compared to the angled panels with no horizontal cable management however….<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u> <u></u></span></p><div><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d">Thanks,<u></u><u></u></span></p>
<p class="MsoNormal"><b><span style="font-family:"Arial","sans-serif";color:#333333">Ayden Beeson</span></b><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u><u></u></span></p>
</div><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u> <u></u></span></p><div><div style="border:none;border-top:solid #b5c4df 1.0pt;padding:3.0pt 0cm 0cm 0cm">
<p class="MsoNormal"><b><span lang="EN-US" style="font-size:10.0pt;font-family:"Tahoma","sans-serif"">From:</span></b><span lang="EN-US" style="font-size:10.0pt;font-family:"Tahoma","sans-serif""> AusNOG [mailto:<a href="mailto:ausnog-bounces@lists.ausnog.net" target="_blank">ausnog-bounces@lists.ausnog.net</a>] <b>On Behalf Of </b>Beeson, Ayden<br>
<b>Sent:</b> Tuesday, 27 May 2014 4:28 PM<br><b>To:</b> <a href="mailto:James.Baird@gwf.com.au" target="_blank">James.Baird@gwf.com.au</a>; Paul Gear</span></p><div><div class="h5"><br><b>Cc:</b> <a href="mailto:ausnog@lists.ausnog.net" target="_blank">ausnog@lists.ausnog.net</a>; AusNOG<br>
<b>Subject:</b> Re: [AusNOG] Improving rack density with different cable management<u></u><u></u></div></div><p></p></div></div><div><div class="h5"><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d">I can’t agree more. We use Panduit angled panels with the side cable management, it is amazing.<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d">Even with standard 24 port 1RU panels you can get a LOT more ports into the same space….<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d">For really high density installs Panduit do a make a 48 port 1 RU HD minicom panel too though I would have assumed as was said earlier that it would be a real pain to work with….<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d">Thanks,<u></u><u></u></span></p>
<p class="MsoNormal"><b><span style="font-family:"Arial","sans-serif";color:#333333">Ayden Beeson</span></b><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1f497d"><u></u> <u></u></span></p><p class="MsoNormal"><b><span lang="EN-US" style="font-size:10.0pt;font-family:"Tahoma","sans-serif"">From:</span></b><span lang="EN-US" style="font-size:10.0pt;font-family:"Tahoma","sans-serif""> AusNOG [mailto:<a href="mailto:ausnog-bounces@lists.ausnog.net" target="_blank">ausnog-bounces@lists.ausnog.net</a>] <b>On Behalf Of </b><a href="mailto:James.Baird@gwf.com.au" target="_blank">James.Baird@gwf.com.au</a><br>
<b>Sent:</b> Tuesday, 27 May 2014 4:10 PM<br><b>To:</b> Paul Gear<br><b>Cc:</b> <a href="mailto:ausnog@lists.ausnog.net" target="_blank">ausnog@lists.ausnog.net</a>; AusNOG<br><b>Subject:</b> Re: [AusNOG] Improving rack density with different cable management<u></u><u></u></span></p>
<p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal" style="margin-bottom:12.0pt"><br><span style="font-size:10.0pt;font-family:"Arial","sans-serif"">+1 to Panduit, if you can install 750mm wide racks. Angled patch panels + side mounted vertical cable management. Easily fits 480 ports per rack.</span> <br>
<span style="font-size:10.0pt;font-family:"Arial","sans-serif""><a href="https://www.dropbox.com/s/wkadtc8us5sxdql/20140527_155329.jpg" target="_blank">https://www.dropbox.com/s/wkadtc8us5sxdql/20140527_155329.jpg</a></span> <br>
<br><br><br><u></u><u></u></p><table border="0" cellpadding="0" width="100%" style="width:100.0%"><tbody><tr><td width="40%" valign="top" style="width:40.0%;padding:.75pt .75pt .75pt .75pt"><p class="MsoNormal"><b><span style="font-size:7.5pt;font-family:"Arial","sans-serif"">Paul Gear <<a href="mailto:ausnog@libertysys.com.au" target="_blank">ausnog@libertysys.com.au</a>></span></b><span style="font-size:7.5pt;font-family:"Arial","sans-serif""> </span><br>
<span style="font-size:7.5pt;font-family:"Arial","sans-serif"">Sent by: "AusNOG" <<a href="mailto:ausnog-bounces@lists.ausnog.net" target="_blank">ausnog-bounces@lists.ausnog.net</a>></span> <u></u><u></u></p>
<p><span style="font-size:7.5pt;font-family:"Arial","sans-serif"">05/27/2014 03:36 PM</span> <u></u><u></u></p></td><td width="59%" valign="top" style="width:59.0%;padding:.75pt .75pt .75pt .75pt"><table border="0" cellpadding="0" width="100%" style="width:100.0%">
<tbody><tr><td valign="top" style="padding:.75pt .75pt .75pt .75pt"><p class="MsoNormal" align="right" style="text-align:right"><span style="font-size:7.5pt;font-family:"Arial","sans-serif"">To</span><u></u><u></u></p>
</td><td valign="top" style="padding:.75pt .75pt .75pt .75pt"><p class="MsoNormal"><span style="font-size:7.5pt;font-family:"Arial","sans-serif""><a href="mailto:ausnog@lists.ausnog.net" target="_blank">ausnog@lists.ausnog.net</a></span> <u></u><u></u></p>
</td></tr><tr><td valign="top" style="padding:.75pt .75pt .75pt .75pt"><p class="MsoNormal" align="right" style="text-align:right"><span style="font-size:7.5pt;font-family:"Arial","sans-serif"">cc</span><u></u><u></u></p>
</td><td valign="top" style="padding:.75pt .75pt .75pt .75pt"></td></tr><tr><td valign="top" style="padding:.75pt .75pt .75pt .75pt"><p class="MsoNormal" align="right" style="text-align:right"><span style="font-size:7.5pt;font-family:"Arial","sans-serif"">Subject</span><u></u><u></u></p>
</td><td valign="top" style="padding:.75pt .75pt .75pt .75pt"><p class="MsoNormal"><span style="font-size:7.5pt;font-family:"Arial","sans-serif"">[AusNOG] Improving rack density with different cable management</span><u></u><u></u></p>
</td></tr></tbody></table><p class="MsoNormal"><u></u> <u></u></p><table border="0" cellpadding="0"><tbody><tr><td valign="top" style="padding:.75pt .75pt .75pt .75pt"></td><td valign="top" style="padding:.75pt .75pt .75pt .75pt">
</td></tr></tbody></table><p class="MsoNormal"><u></u><u></u></p></td></tr></tbody></table><p class="MsoNormal" style="margin-bottom:12.0pt"><br><br><br><tt><span style="font-size:10.0pt">Hi all,</span></tt><span style="font-size:10.0pt;font-family:"Courier New""><br>
<br><tt>Most of our sites have fairly simple cable management using traditional </tt><br><tt>cable management like this: </tt><br><tt><a href="https://www.dropbox.com/s/nc7bmgs7j85laeq/20140527_145239.jpg" target="_blank">https://www.dropbox.com/s/nc7bmgs7j85laeq/20140527_145239.jpg</a></tt><br>
<br><tt>This is easy to work with in most cases where we don't have high port </tt><br><tt>counts. However, once you push 48 Cat6 cables into them they can get a </tt><br><tt>bit tight.</tt><br><br><tt>We have some new sites which are coming online that require up to 288 </tt><br>
<tt>ports per floor, and these will not fit in the single rack provided for </tt><br><tt>the floor if we use traditional cable management, once all the patching, </tt><br><tt>switching, and UPS requirements are taken into account. We will still </tt><br>
<tt>have 750-800 mm wide racks, so I was hoping to find something that could </tt><br><tt>be mounted at the side of the rack and protrude towards the front, so </tt><br><tt>that we could use all the rack frontage for either patch panels or </tt><br>
<tt>switch ports. Some larger chassis switches seem to have this sort of </tt><br><tt>thing built in, e.g. </tt><br><tt><a href="http://product-images.www8-hp.com/digmedialib/prodimg/lowres/c03131047.png" target="_blank">http://product-images.www8-hp.com/digmedialib/prodimg/lowres/c03131047.png</a></tt><br>
<br><tt>Searching Google suggests that there are plenty of options which look OK </tt><br><tt>for low-density deployment, e.g. </tt><br><tt><a href="http://www.fibersavvy.com/store/i/is.aspx?path=/Shared/images/21_Cable%20Management/PP4-3197-1U_04.jpg&lr=t&bw=550&w=550&bh=550&h=550" target="_blank">http://www.fibersavvy.com/store/i/is.aspx?path=/Shared/images/21_Cable%20Management/PP4-3197-1U_04.jpg&lr=t&bw=550&w=550&bh=550&h=550</a> </tt><br>
<tt>but putting up to 48 Cat6 cables on that would not work, in my opinion. </tt><br><tt>What I was hoping to find is something that would allow cables to be </tt><br><tt>laid in horizontally, more like the L-shaped lower part of our existing </tt><br>
<tt>Krone cable management, but a little longer and a little wider (say, </tt><br><tt>70-90mm deep and 30mm wide), and possibly with a number of different </tt><br><tt>channels in it to separate different groups of cables.</tt><br>
<br><tt>Does anyone know of such a system? Are there other options which would </tt><br><tt>allow us to cram in better Cat6 port densities?</tt><br><br><tt>Thanks in advance,</tt><br><tt>Paul</tt><br><br><tt>_______________________________________________</tt><br>
<tt>AusNOG mailing list</tt><br><tt><a href="mailto:AusNOG@lists.ausnog.net" target="_blank">AusNOG@lists.ausnog.net</a></tt><br><tt><a href="http://lists.ausnog.net/mailman/listinfo/ausnog" target="_blank">http://lists.ausnog.net/mailman/listinfo/ausnog</a></tt></span><u></u><u></u></p>
<table border="0" cellpadding="0"><tbody><tr><td style="background:white;padding:.75pt .75pt .75pt .75pt"><pre><span style="color:black">**************************************************<u></u><u></u></span></pre><pre><span style="color:black">This email and its attachments are confidential and subject to copyright. If they have come to you in error please notify us immediately by return mail, and then delete the email. You should take no action based upon the contents nor should you use, copy or show them to anyone.<u></u><u></u></span></pre>
<pre><span style="color:black">Any views or opinions expressed are those of the author and do not necessarily represent those of George Weston Foods Ltd.<u></u><u></u></span></pre><pre><span style="color:black">Security: Internet email is not a secure medium; please note this when considering the content of your message.<u></u><u></u></span></pre>
<pre><span style="color:black">Viruses: GWF takes precaution to ensure email is free of viruses but cannot guarantee this. GWF scans all in and outbound email and attachments, however GWF accepts no liability for damage caused by this email or the attachments due to virus interference, interception, corruption or unauthorised access.<u></u><u></u></span></pre>
<pre><span style="color:black"><u></u> <u></u></span></pre><pre><span style="color:black">Please consider our environment before printing this email.<u></u><u></u></span></pre><pre><span style="color:black">**************************************************<u></u><u></u></span></pre>
</td></tr></tbody></table><p class="MsoNormal"><u></u> <u></u></p><p><a href="http://www.csu.edu.au/" title="Charles Sturt University" target="_blank"><span style="text-decoration:none"><img border="0" width="210" height="60" src="cid:image001.png@01CF79C9.04925500" alt="Charles Sturt University"></span></a><u></u><u></u></p>
<p><span style="font-size:6.0pt;font-family:"Arial","sans-serif";color:#c42129">| ALBURY-WODONGA | BATHURST | CANBERRA | DUBBO | GOULBURN | MELBOURNE | ONTARIO | ORANGE | PORT MACQUARIE | SYDNEY | WAGGA WAGGA |<u></u><u></u></span></p>
<div class="MsoNormal" align="center" style="text-align:center"><hr size="2" width="100%" align="center"></div><p class="MsoNormal"><b><span style="font-size:7.0pt;font-family:"Arial","sans-serif"">LEGAL NOTICE</span></b><br>
<span style="font-size:7.0pt;font-family:"Arial","sans-serif"">This email (and any attachment) is confidential and is intended for the use of the addressee(s) only. If you are not the intended recipient of this email, you must not copy, distribute, take any action in reliance on it or disclose it to anyone. Any confidentiality is not waived or lost by reason of mistaken delivery. Email should be checked for viruses and defects before opening. Charles Sturt University (CSU) does not accept liability for viruses or any consequence which arise as a result of this email transmission. Email communications with CSU may be subject to automated email filtering, which could result in the delay or deletion of a legitimate email before it is read at CSU. The views expressed in this email are not necessarily those of CSU.</span> <u></u><u></u></p>
<p><span style="font-size:7.0pt;font-family:"Arial","sans-serif""><a href="http://www.csu.edu.au" target="_blank"><span style="color:#c42129">Charles Sturt University in Australia</span></a> The Grange Chancellery, Panorama Avenue, Bathurst NSW Australia 2795 (ABN: 83 878 708 551; CRICOS Provider Number: 00005F (National)). TEQSA Provider Number: PV12018 <br>
<a href="http://www.charlessturt.ca/" target="_blank"><span style="color:#c42129">Charles Sturt University in Ontario</span></a> 860 Harrington Court, Burlington Ontario Canada L7N 3N4 Registration: <a href="http://www.peqab.ca" target="_blank"><span style="color:#c42129">www.peqab.ca</span></a><u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size:7.0pt;font-family:"Arial","sans-serif"">Consider the environment before printing this email.</span> <u></u><u></u></p><div><p class="MsoNormal"><span style="font-size:8.5pt;font-family:"Verdana","sans-serif";color:#999999"><br>
Disclaimer added by <b>CodeTwo Exchange Rules 2007</b><br><a href="http://www.codetwo.com" target="_blank">www.codetwo.com</a><u></u><u></u></span></p></div><p class="MsoNormal"><u></u> <u></u></p></div></div></div></div>
<br>_______________________________________________<br>
AusNOG mailing list<br>
<a href="mailto:AusNOG@lists.ausnog.net">AusNOG@lists.ausnog.net</a><br>
<a href="http://lists.ausnog.net/mailman/listinfo/ausnog" target="_blank">http://lists.ausnog.net/mailman/listinfo/ausnog</a><br>
<br></blockquote></div><br></div>